13 September 2017
Spooky Remote v2.0 added
Spooky Boost v3.1 added
28 May 2017
Spooky 10-port USB 3.0 Hub added
Spooky Quad 5v Power Supply added
Spooky Conductive Carbonized Rubber Hand Cylinders added
Spooky2 kits updated
You can greatly increase the power of Spooky2 by adding any or all of the accessories below. Whether you want to search for anomalous frequencies in the body, supercharge your remote transmission power, or simply enhance your Spooky rig connectivity, Spooky2 has you covered.
Click on any image to view that accessory's page on the Spooky2-Mall website.
Finding frequencies in the body that that correspond to viruses, bacteria, and parasites is simplicity itself with this little fellow. Plug him in and attach his clip to your earlobe. Or, if you choose the fingerclip version, attach it to a finger. Click any red Channel button in Spooky2 to open its Control panel. Enter the range of frequencies you want to investigate in the Start and Finish Frequency fields. Then enter the Initial Step Size for the search, the number of decimal places of accuracy you want, the number of hits you wish to find, and hit Scan. Or simply choose the preset we've provided for biofeedback, then enter your own range and settings.
Now grab your electrodes, lie down, close your eyes, and relax completely. Spooky2 will "ping" your body with a sweep through the frequency range you entered, noting any 'hits" or echoes it receives. When it's done, it returns to all the hits found and automatically sweeps around them until it finds the exact frequency that generates the strongest responses. These are then written to memory, and you can choose to save them to file in your own custom database when the process is complete.
You don't have to use Spooky Hand Cylinders though - you can use Spooky TENS pads or a Spooky Remote to transmit them instead.
Depending on your range settings - and your own heart rate - the average session takes 10-90 minutes, and you then have your own personal custom frequency set to experiment with anomalies detected in your scan.
Spooky Pulse comes bundled in almost all our kits.
Spooky Cold Laser Wrist/Twin
Cold laser, also called Low Level Laser Therapy (LLLT), uses safe non-thermal light photons to accelerate the body's natural healing processes. This light energy can penetrate right through all the layers of our skin with ease. It's especially useful for pain, joint and neurological problems, wounds and burns, dental issues, lymph node swelling, tinnitus, and bone/tissue regeneration, plus many more applications.
While researching cancer cells in 1974, Prof. Fritz-Albert Popp made the astounding discovery that all cells store photons of light, particularly around DNA. He showed that cancer and other diseased cells have a significantly different level of photon emission to normal cells, and theorized that this stored internal light may be a major part of how cells communicate with each other in the body to maintain overall health. Subsequent Russian DNA research validated his findings. The therapeutic uses of cold laser are backed by many medical studies.
Cold laser therapy is normally applied for 30 minutes, but longer times are fine. Spooky Cold Laser Wrist is designed to be worn around the wrist, where it can easily treat the entire blood supply, the carpal tunnel, and the meridian complex, but it can also be used on other areas. Spooky Cold Laser Twin is used for pinpoint application to any area of the body, and can be used in the mouth, or inserted into ear canals and nostrils.
Either unit connects directly to Out 1 of a Spooky2-5M generator, or to Out 1 of a Spooky Boost 3.0, and can be pulsed by frequencies. Both units come as standard with almost every kit.
Spooky PEMF Coil
This is our PEMF (Pulsed ElectroMagnetic Field) coil. It comes as standard with Spooky Central, but this version can be connected directly to Out 1 of a Spooky2-5M generator using the BNC to 6.3 mm mono adaptor that comes with it. You can also connect it to Out 1 of a Spooky Boost 3.0, or to its High Power Contact output. Adding a BNC Female-to-Female connector enables connection to the BN or MN outputs.
If you already own a Spooky Central, you can connect its included Spooky Coil to a generator with this very inexpensive adaptor.
Use with a generator is very suitable for healing/frequency entrainment. By laying it on a flat surface and placing a glass of water on top of the coil, you can also imprint a frequency of your choice into the water. Or insert a vial in the central opening.
Spooky Remote v2.0
This is how scalar wave creation should be done. No Mobius coils - all that's needed is a pair of dual-layer planar coils arranged as a "sandwich," then boost the magnetic field more than 12,000 times by incorporating a super-powerful neodymium magnet. Enclose your specimen in paper masking tape, insert it into the sandwich as the "filling" so that the specimen sits beneath the circular magnet - and prepare to be surprised at the raw scalar power.
Spooky Remote v2.0 comes complete with a 500mm (19.5in) BNC cable. No assembly required. Comes with almost all our kits.
Spooky Boost 3.1
Spooky Boost v3.1
This clever signal processor connects to both Outs of your Spooky2-5M frequency generator, providing six individually-purposed outputs.
Out 1 and Out 2 are pass-through connections. They provide the individual signals from the generator's Outs unprocessed. You can use these to connect two sets of Spooky Hand Cylinders (see below), or one plus a set of footplates. It's also possible to connect the original Spooky Boost cable to these to provide another two outputs. In this case, the amplitude will be shared. We don't recommend doing this.
The Colloidal Silver output has additional components in its circuit, mixing and processing the generator's summed outputs for optimum manufacture of very high quality colloidal silver. You can also use this output to connect a single set of Spooky Hand Cylinders for Contact Mode - this will provide an attenuated signal. If you prefer to maintain complete amplitude control, you can use the High Pwr Contact output.
The BN output is configured to drive a Spooky Remote v1.1 Bio North, while the MN one is used for the Magnetic North model.
Why would you want to use this?
Well, Spooky Boost 3.1 can quadruple the generator's power in Contact Mode.
In Remote Mode, it enables you to mix two waveforms/frequencies and transmit the result from one Spooky Remote. This allows you to run Programs that used to require two Remotes on just one instead - effectively doubling the power and effectiveness of your transmission.
For Plasma Mode users, the extra power that Spooky Boost 3.1 provides can allow direct driving of some power amplifiers. A Spooky Central should be connected to Out 1 and Out 2 only.
Comes as standard with almost all our kits.
Spooky Carbonized Rubber Hand Cylinders
Hand cylinder electrodes that come with many commercial machines are made from industrial-grade copper or stainless steel tubing. Spooky Conductive Carbonized Rubber Hand Cylinders are made from high quality electrically conductive rubber. Their dimpled design maximizes skin contact and comfort.
Connect them to a Spooky Boost 3.0, or directly to your Spooky2-5M generator if lower power is desirable. Connection requires the Spooky TENS cable, which must be purchased separately. These hand cylinders and cable come bundled in almost all our kits.
Spooky USB 3.0 Hub
Spooky USB 3.0 Hub
When you're using multiple generators, USB connectivity can be a headache. Not anymore. Here's our solution - the durable Spooky 10-port USB 3.0 powered hub allows you to connect up to 10 generators to a single USB port on your computer, ensuring more reliable Spooky2 rig operation for an unbelievable price.
Spooky Quad 5v Power Supply
If you're tired of wrestling with a messy tangle of wires, here's the answer - this clever power supply can drive up to four Spooky2-5M generators at once using a single wall socket. Best of all, our price is right (as usual).
We're very proud to introduce the latest powerful addition to our Spooky2 family - Spooky Radionics v1.1. This beautiful and compact device was specially designed for us by Berkana Labs, an artisan British company with a history of building awesome - and elegant - radionics machines.
Powered by a Spooky2-5M generator, Spooky Radionics can be used for treatment and diagnostics. It can narrowcast just like a Spooky Remote, using DNA on the Output plate and transmitting via scalar energy. But it's capable of much more. You can run frequencies and augment them with radionics "rates" using the three dials. You can then add any healing/beneficial substance - or crystal - to the Input plate. Spooky Radionics will detect its energy field and mix it to the total Output signal.
However, you're not limited to transmitting via DNA. You can place a dropper bottle with distilled water on the Output plate, then "imprint" it with frequencies and rates, PLUS whatever you put on the Input plate. You can also use this method to copy or clone any remedy you like. You don't have to use ingestibles either - you can program a healing crystal instead and carry it on your person.
Diagnostics can be done by placing a DNA sample on the Input plate, then turning each dial while holding a pendulum or using the Output as a "stick plate." Once you've found the rate for the problem, you can easily calculate the rate needed to reverse it, and either transmit it via DNA or create a remedy for it.
With Spooky Radionics, the possibilities are limited only by your imagination and inventiveness.
Coming in 2017 is our latest addition - the Spooky Radionics 12-dial unit. Plus a range of accessories that will add power, function, and value. Click the image to buy/order. Download the manual here.
There are five different handy kits available to simplify your choices - three are shown below:
Spooky2 Starter's Kit: this comes with one Spooky2-5M frequency generator, one Spooky Remote v1.1 Bio North, Spooky Pulse, both Spooky Cold Lasers, and all the gear you need to get started right out of the box.
Spooky2 Essential Kit for Cancer, Lyme, and Morgellons: this includes two generators, two Spooky Remote v1.1 Bio Norths, Spooky Pulse, both Spooky Cold Lasers, and all the gear you need to get started right out of the box.
Spooky2 Advanced Kit for Cancer, Lyme, and Morgellons: this includes four generators, four Spooky Remote v1.1 Bio Norths, Spooky Pulse, both Spooky Cold Lasers, and all the gear you need to get started right out of the box.
Spooky2 Home Care Kit: designed for home insect pest and mould remediation, this includes one generator, a Spooky Boost 3.0, and one Spooky Remote v1.1 Bio North. It's here.
Spooky2 Colloidal Silver Kit: this comes with a Spooky Boost 3.0 and two 300mm long 2.5mm diameter certified 99.99% pure silver rods. See it here.